CXA-L10A (4.5w dual outputs, pcb mountable type) dc-ac inverter unit (standard) power systems ? the power solution web: www.power-systems.de address: d?rnet 8 ; 74360 ilsfeld-auenstein / germany email: info@power-systems.de tel. : + 49 / 70 62 / 67 59 - 6 fax: + 49 / 70 62 / 67 59 - 80 all specification are subject to change without notice. page ( 1 / 4 ) ver, 04 october 2002 description : tdk dc/ac inverter, cxa-series, are low-noise, high frequency power sources developed for driving cold cathode fluorescent lamps operating at 20~80 khz. these inverters are designed to handle a wide range of lamp characteristics. features : constant current output ensures compatibility with a wide range of discharge lamps. high efficiency resonant circuitry produces low-noise, sinusoidal-wave output. one-lamp/two-lamp combined-use capability allows use in four different configurations. common ground or floating bulb configurations. compact size and light weight facilitate pc board mounting. high efficiency (80%) fuse protection temperature & humdity : operating temperature range -10 c ~ +60 c storage temperature range -20 c ~ +85 c humidity 95 %rh max (no dew) dimensions : (bottom view) unit : mm weight : 11.2 (g) typ. *1 remove for isolated ground 21max 16.5 0.2 15.24 0.2 0.5 0.2 44max 38.1 0.2 5.08 0.2 (9) (5) 26 0.2 7.5 0.2 3- 1.6 0.15 r1.15 0.2 jumper (*1) 13max 5min 5- 0.8 0.1 or 5- 0.64 0.07 12 3 4 5 (1.0) (solder plated obstinate copper wire) (side view)
CXA-L10A (4.5w dual outputs, pcb mountable type) dc-ac inverter unit (standard) power systems ? the power solution web: www.power-systems.de address: d?rnet 8 ; 74360 ilsfeld-auenstein / germany email: info@power-systems.de tel. : + 49 / 70 62 / 67 59 - 6 fax: + 49 / 70 62 / 67 59 - 80 all specification are subject to change without notice. page ( 2 / 4 ) ver, 04 october 2002 connector configuration: electrical characteristics: vin [v] ta [c] rl [k min. typ. max. 50.05 235 30 9 10 11 50.25 -10~60 23~37 8 10 12 input current iin 50.25 -10~60 23~37 - 800 1200 ma dc frequency f 50.25 -10~60 23~37 25 30 35 khz open circuit voltage vopen 50.25 -10~60 800 900 - vrms 50.05 235 50 5.2 6 6.6 50.25 -10~60 38~62 4.6 6 7.2 input current iin 50.25 -10~60 38~62 - 510 770 ma dc frequency f 50.25 -10~60 38~62 30 35 40 khz open circuit voltage vopen 50.25 -10~60 800 900 - vrms 50.05 235 60 4.5 5 5.6 50.25 -10~60 45~75 4.0 5 6.1 input current iin 50.25 -10~60 45~75 - 450 680 ma dc frequency f 50.25 -10~60 45~75 25 30 35 khz open circuit voltage vopen 50.25 -10~60 800 900 - vrms 50.05 235 60 4.5/4.5 5/5 5.5/5.5 50.25 -10~60 45~75 4/4 5/5 6/6 input current iin 50.25 -10~60 45~75 - 800 1200 ma dc frequency f 50.25 -10~60 45~75 25 30 35 khz open circuit voltage vopen 50.25 -10~60 800 900 - vrms 3 4 marms marms marms output current iout output current connection 1 2 marms items symbols conditions specification unit iout output current iout output current iout1 / iout2 pin no. symbols ratings 1 vin 5v 2 gnd 0v 3 out1 300vrms 4 out2 300vrms 5 out gn d 0v items symbols specification unit input voltage vin 0~6.0 vdc output power pout 4.5 w absolute maximum ratings:
CXA-L10A (4.5w dual outputs, pcb mountable type) dc-ac inverter unit (standard) power systems ? the power solution web: www.power-systems.de address: d?rnet 8 ; 74360 ilsfeld-auenstein / germany email: info@power-systems.de tel. : + 49 / 70 62 / 67 59 - 6 fax: + 49 / 70 62 / 67 59 - 80 all specification are subject to change without notice. page ( 3 / 4 ) ver, 04 october 2002 application: pin 3(iout1) pin 5(iout-ret) pin 1 (vin) pin 2(gnd) vin ccfl rl connection 1 pin 4(iout2) pin 3(iout1) pin 5(iout-ret) pin 1 (vin) pin 2(gnd) vin ccfl rl connection 2 pin 4(iout2) pin 3(iout1) pin 5(iout-ret) pin 1 (vin) pin 2(gnd) vin ccfl rl connection 3 pin 4(iout2) pin 3(iout1) pin 5(iout-ret) pin 1 (vin) pin 2(gnd) vin ccfl1 rl connection 4 pin 4(iout2) ccfl2 rl note 1. for circuit connection, pleas e prefer to test circuit diagram. note 2. please use minimum of 2mm clearance (all directions) between inverter high voltage area and any conductors. please refer to mechanical drawing for marking of high voltage area. note 3. open voltage (strike voltage) is measured acro ss the transformer secondary winding at no load as the reading at the output connector would be less than the actual value. note 4. if the start up voltage falls below cold cathode tube strike voltage, the ccfl will not light up easily specially at lower ambient temperature. pleas e review mounting instruction to avoid any abnormal operation due to coupling/leakage capacitance of in verter high voltage area to any surrounding conductor. note 5. for operation in floating mode, please remove jumper (j1) on top side of pcb that pin2 and pin5. note 6. to prevent electrical discharge from high volt age area, please use non-conductive fastener in u mounting hole.
CXA-L10A (4.5w dual outputs, pcb mountable type) dc-ac inverter unit (standard) power systems ? the power solution web: www.power-systems.de address: d?rnet 8 ; 74360 ilsfeld-auenstein / germany email: info@power-systems.de tel. : + 49 / 70 62 / 67 59 - 6 fax: + 49 / 70 62 / 67 59 - 80 all specification are subject to change without notice. page ( 4 / 4 ) ver, 04 october 2002 connection test circuit notes 1 lin (1) vin out1 (3) out2(4) lout short of out 1,out2 rl open of out2 a v a vin (2)gnd 1000:1 v 2 lin (1) vin out1 (3) out2 (4) lout rl a v a vin (2) gnd 1000:1 v nc 4 lin (1)vin out1(3) out2 (4) a a vin (2)gnd 1000:1 v lout1 rl2 lout2 rl1 a a out gnd(5) out gnd(5) out gnd(5) short of out2,out gnd 3 lin (1)vin out1 (3) out2(4) lout rl a v a vin (2) gnd 1000:1 v out gnd(5) test circuit:
|
